Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
linux:evo [2008/03/15 22:10] faith |
linux:evo [2008/03/16 19:49] faith |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Compaq Evo T30 ====== | ====== Compaq Evo T30 ====== | ||
| + | |||
| + | |||
| Line 17: | Line 19: | ||
| From cracking the case: | From cracking the case: | ||
| - | * National Geode CS5530A-UCE (AMD now makes this chip) | + | * National Geode CS5530A-UCE (this is the southbridge, now made by AMD) |
| + | * Geode processor under heat sink on bottom of board | ||
| This suggests the model I have is similar to the 238617-xxx (DK408A) | This suggests the model I have is similar to the 238617-xxx (DK408A) | ||
| Line 50: | Line 53: | ||
| * Got [[an>evo/netxfer.sh]] from http://thunderlord.net.pl/evo/files/netxfer.sh | * Got [[an>evo/netxfer.sh]] from http://thunderlord.net.pl/evo/files/netxfer.sh | ||
| * Got the [[an>evo/sp27933.exe | Evo T30 32/64 Rapport Package to Add CE.NET Firmware 4.0 B472.6 29 Apr 2004]] from [[http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=96324&prodNameId=97153&swEnvOID=1054&swLang=13&mode=2&taskId=135&swItem=PSG_I20941-104856 | HP]] | * Got the [[an>evo/sp27933.exe | Evo T30 32/64 Rapport Package to Add CE.NET Firmware 4.0 B472.6 29 Apr 2004]] from [[http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=96324&prodNameId=97153&swEnvOID=1054&swLang=13&mode=2&taskId=135&swItem=PSG_I20941-104856 | HP]] | ||
| + | |||
| ==== Initial Firmware Download ==== | ==== Initial Firmware Download ==== | ||
| Line 59: | Line 63: | ||
| * Edit ''netxfer.sh'' to change all /home/blah to /tmp/evo. | * Edit ''netxfer.sh'' to change all /home/blah to /tmp/evo. | ||
| * Power up the Evo T30 while pressing the 'p' key (while the LED is orange), getting to the screen shown above. | * Power up the Evo T30 while pressing the 'p' key (while the LED is orange), getting to the screen shown above. | ||
| - | * sh ''netxfer.sh'' (I tried with my normal dhcpd and tftp setup, but that's not good enough. We need to be running on special ports. I did not have to configure any special IP addresses.) | + | * sh ''netxfer.sh'' (I tried with my normal dhcpd and tftp setup, but that's not good enough. We need to be running on special ports for the Evo to communicate -- these ports are set up by this script. I did not have to configure any special IP addresses.) |
| * After the servers started and a few seconds passed, the T30 started printing stuff. | * After the servers started and a few seconds passed, the T30 started printing stuff. | ||
| * If you get the "error: not a tagged image" error, you might have used sp27933.exe directly instead of extracting its contents. | * If you get the "error: not a tagged image" error, you might have used sp27933.exe directly instead of extracting its contents. | ||